a casa
Sobre nosaltres
Perfil de la companyia
Història de l'empresa
El nostre avantatge
Els nostres productes
CrMo Mill Liner
Mn Steel Mill Liner
Cr Steel Mill Liner
Revestiment de molí d'acer d'aliatge
Peces de la trituradora de mandíbula
Peces de la trituradora de con
Peces de la trituradora de martell
Peces de la trituradora d'impacte
Mitjans de trituració
Altres peces de recanvi
Servei
El nostre servei
Notícies
Contacta amb nosaltres
Anglès
a casa
Notícies
Notícies de la indústria
Ratio de desgast de les peces de desgast de la trituradora de mandíbules
per administrador el 20-11-13
Jaw Crusher Wear Parts Wear Ratio Jaw crusher wear parts include: Upper cheek plates Lower cheek plates Movable jaw Fixed jaw In normal working conditions, different wear parts have different wear ratios. In order to avoid damage the jaw crusher, we must know every wear part wear ratio....
Llegeix més
Comparacions entre disseny de placa de mandíbula d'1 peça i 2 peces
per administrador el 20-11-13
Comparisons Between 1 piece and 2 piece jaw plate design There are some jaw plates are designed to 1 piece or 2 pieces. Different designs suit different jaw crushers and working conditions. Normally, large jaw crusher jaw plates are originally designed to use a 2 piece jaw die design, whi...
Llegeix més
Placa intermèdia de trituradora de mandíbules
per administrador el 20-11-13
Jaw Crusher Intermediate Plate The intermediate plate is an important jaw crusher wear parts. Fitting an intermediate (backing) plate behind the fixed jaw die reduces the nip angle of the crusher. The intermediate plate reduces the feed opening and the setting range by approximately the s...
Llegeix més
Placa de protecció de la trituradora de mandíbules
per administrador el 20-11-13
Jaw Crusher Protection Plate Protection plates are designed for additional protection of the crusher’s frame and pitman. They are recommended when using small settings (always greater than or equal to the minimum recommended setting) and/or when the rock to be crushed is very hard (i.e. v...
Llegeix més
RECAMBIO DE PLACA DE 1 PEÇA DE MORDA
per administrador el 20-11-13
1 PIECE JAW Plate REPLACEMENT Jaw plates can either be turned end for end or replaced depending on their wear. The jaw dies can be turned once after their installation before they need to be replaced. Dismantling Fixed Jaw Plates Clean the jaw die lifting holes. Remove stones and sand f...
Llegeix més
SUBSTITUCIÓ DE MATÈRES DE 2 PICES
per administrador el 20-11-13
2 PIECE JAW DIE REPLACEMENT Jaw dies can either be turned end for end or replaced depending on their wear. The jaw dies can be turned once after their installation before they need to be replaced. Fixed Jaw Die Clean the jaw die lifting holes. Remove stones and sand from the jaws. Remo...
Llegeix més
Cambra de trituració de la trituradora de mandíbules
per administrador el 20-11-13
Jaw Crusher Crushing Chamber To ensure optimum performance and cost-effective production it’s important to frequently inspect the following parts and to replace them before they are completely worn out. 3500-0 Deflector plate (moving jaw only) 3400-0 Clamping bar 3300-1 Jaw plate 3100-0...
Llegeix més
Sistema d'ajust de la trituradora de mandíbules
per administrador el 20-11-13
Jaw Crusher Setting Adjustment System Maintenance for these parts must be carried out only by trained or authorized personnel, but the inspection can be performed by the operator. Worn components should be replaced in good time to avoid damaging the toggle plate or toggle seats, with a co...
Llegeix més
Canvi de placa de mandíbula
per administrador el 20-11-13
Exchanging jaw plate After a long time running, jaw plates need an exchange. The following wear parts are required: A new fixed jaw plate A new movable jaw plate Never weld external lifting eyes to the jaw plates. Always use the referred lifting cavity on the jaw plate and the lifting ...
Llegeix més
Com instal·lar la placa de la mandíbula?
per administrador el 20-11-13
Installing jaw plate There are some things that need to notice when installing jaw plates. 3500-0 Deflector plate (moving jaw) 3300-1 Jaw plate 3100-0 Wear plate 3200-0 Support bar. 1 Lifting cavity,2 Lifting tool. If planning to exchange wear plates (3100-0), cheek plates, deflector p...
Llegeix més
Canvi de placa de desgast de la trituradora de mandíbules
per administrador el 20-11-13
Exchanging jaw crusher wear plate How to exchange jaw crusher wear plates? What needs notice when exchanging jaw crusher wear plate? 3000-0 Jaw (moving) 3100-0 Wear plate 3200-0 Support bar 3200-1 Lifting eye Recommended tools: Crow bar, Lifting tackle, and chain Mobile crane The follo...
Llegeix més
Canvieu i instal·leu la placa de galta de la trituradora de mandíbules
per administrador el 20-11-13
Exchange and Install Jaw Crusher Cheek Plate Cheek plates are one of the most important jaw crusher wear parts. After a long time working, those cheek plates need exchange. How to exchange jaw crusher cheek plates? How to install jaw crusher cheek plates? How to exchange jaw crusher chee...
Llegeix més
1
2
3
4
5
6
Següent >
>>
Pàgina 1 / 14
Premeu Intro per cercar o ESC per tancar
English
Catalan
French
German
Portuguese
Spanish
Russian
Japanese
Korean
Arabic
Irish
Greek
Turkish
Italian
Danish
Romanian
Indonesian
Czech
Afrikaans
Swedish
Polish
Basque