الصفحة الرئيسية
معلومات عنا
ملف الشركة
تاريخ الشركة
منفعتنا
منتجاتنا
بطانة مطحنة CrMo
بطانة مطحنة الصلب Mn
بطانة مطحنة الصلب Cr
بطانة مطحنة سبائك الصلب
أجزاء كسارة الفك
أجزاء الكسارة المخروطية
أجزاء كسارة المطرقة
أجزاء الكسارة الصدمية
طحن وسائل الإعلام
قطع غيار أخرى
خدمة
خدمتنا
أخبار
اتصل بنا
إنجليزي
الصفحة الرئيسية
أخبار
اخبار الصناعة
نسبة تآكل قطع غيار كسارة الفك
بواسطة مشرف في 20-11-13
Jaw Crusher Wear Parts Wear Ratio Jaw crusher wear parts include: Upper cheek plates Lower cheek plates Movable jaw Fixed jaw In normal working conditions, different wear parts have different wear ratios. In order to avoid damage the jaw crusher, we must know every wear part wear ratio....
اقرأ أكثر
مقارنات بين تصميم لوحة الفك قطعة واحدة وقطعتين
بواسطة مشرف في 20-11-13
Comparisons Between 1 piece and 2 piece jaw plate design There are some jaw plates are designed to 1 piece or 2 pieces. Different designs suit different jaw crushers and working conditions. Normally, large jaw crusher jaw plates are originally designed to use a 2 piece jaw die design, whi...
اقرأ أكثر
لوحة وسيطة كسارة الفك
بواسطة مشرف في 20-11-13
Jaw Crusher Intermediate Plate The intermediate plate is an important jaw crusher wear parts. Fitting an intermediate (backing) plate behind the fixed jaw die reduces the nip angle of the crusher. The intermediate plate reduces the feed opening and the setting range by approximately the s...
اقرأ أكثر
لوحة حماية كسارة الفك
بواسطة مشرف في 20-11-13
Jaw Crusher Protection Plate Protection plates are designed for additional protection of the crusher’s frame and pitman. They are recommended when using small settings (always greater than or equal to the minimum recommended setting) and/or when the rock to be crushed is very hard (i.e. v...
اقرأ أكثر
1 قطعة استبدال لوحة الفك
بواسطة مشرف في 20-11-13
1 PIECE JAW Plate REPLACEMENT Jaw plates can either be turned end for end or replaced depending on their wear. The jaw dies can be turned once after their installation before they need to be replaced. Dismantling Fixed Jaw Plates Clean the jaw die lifting holes. Remove stones and sand f...
اقرأ أكثر
2 قطعة من قطع الفك استبدال
بواسطة مشرف في 20-11-13
2 PIECE JAW DIE REPLACEMENT Jaw dies can either be turned end for end or replaced depending on their wear. The jaw dies can be turned once after their installation before they need to be replaced. Fixed Jaw Die Clean the jaw die lifting holes. Remove stones and sand from the jaws. Remo...
اقرأ أكثر
غرفة تكسير كسارة الفك
بواسطة مشرف في 20-11-13
Jaw Crusher Crushing Chamber To ensure optimum performance and cost-effective production it’s important to frequently inspect the following parts and to replace them before they are completely worn out. 3500-0 Deflector plate (moving jaw only) 3400-0 Clamping bar 3300-1 Jaw plate 3100-0...
اقرأ أكثر
نظام ضبط ضبط الكسارة الفكية
بواسطة مشرف في 20-11-13
Jaw Crusher Setting Adjustment System Maintenance for these parts must be carried out only by trained or authorized personnel, but the inspection can be performed by the operator. Worn components should be replaced in good time to avoid damaging the toggle plate or toggle seats, with a co...
اقرأ أكثر
تبادل لوحة الفك
بواسطة مشرف في 20-11-13
Exchanging jaw plate After a long time running, jaw plates need an exchange. The following wear parts are required: A new fixed jaw plate A new movable jaw plate Never weld external lifting eyes to the jaw plates. Always use the referred lifting cavity on the jaw plate and the lifting ...
اقرأ أكثر
كيفية تركيب لوحة الفك؟
بواسطة مشرف في 20-11-13
Installing jaw plate There are some things that need to notice when installing jaw plates. 3500-0 Deflector plate (moving jaw) 3300-1 Jaw plate 3100-0 Wear plate 3200-0 Support bar. 1 Lifting cavity,2 Lifting tool. If planning to exchange wear plates (3100-0), cheek plates, deflector p...
اقرأ أكثر
استبدال صفيحة تآكل الكسارة الفكية
بواسطة مشرف في 20-11-13
Exchanging jaw crusher wear plate How to exchange jaw crusher wear plates? What needs notice when exchanging jaw crusher wear plate? 3000-0 Jaw (moving) 3100-0 Wear plate 3200-0 Support bar 3200-1 Lifting eye Recommended tools: Crow bar, Lifting tackle, and chain Mobile crane The follo...
اقرأ أكثر
استبدال وتركيب لوحة الخد كسارة الفك
بواسطة مشرف في 20-11-13
Exchange and Install Jaw Crusher Cheek Plate Cheek plates are one of the most important jaw crusher wear parts. After a long time working, those cheek plates need exchange. How to exchange jaw crusher cheek plates? How to install jaw crusher cheek plates? How to exchange jaw crusher chee...
اقرأ أكثر
1
2
3
4
5
6
التالي>
>>
صفحة 1/14
اضغط على Enter للبحث أو ESC للإغلاق
English
Arabic
French
German
Portuguese
Spanish
Russian
Japanese
Korean
Irish
Greek
Turkish
Italian
Danish
Romanian
Indonesian
Czech
Afrikaans
Swedish
Polish
Basque
Catalan