Hogar
Sobre nosotros
Perfil de la compañía
Historia de la Compañía
Nuestra ventaja
Nuestros productos
Revestimiento de molino CrMo
Revestimiento de molino de acero Mn
Revestimiento de molino de acero Cr
Revestimiento de molino de acero aleado
Piezas de trituradora de mandíbula
Piezas de la trituradora de cono
Partes de la trituradora de martillos
Piezas de la trituradora de impacto
Medios de molienda
Otras piezas de repuesto
Servicio
Nuestro servicio
Noticias
Contáctenos
Inglés
Hogar
Noticias
Noticias de la Industria
Relación de desgaste de las piezas de desgaste de la trituradora de mandíbula
por administrador el 20-11-13
Jaw Crusher Wear Parts Wear Ratio Jaw crusher wear parts include: Upper cheek plates Lower cheek plates Movable jaw Fixed jaw In normal working conditions, different wear parts have different wear ratios. In order to avoid damage the jaw crusher, we must know every wear part wear ratio....
Lee mas
Comparaciones entre el diseño de placa de mordaza de 1 pieza y de 2 piezas
por administrador el 20-11-13
Comparisons Between 1 piece and 2 piece jaw plate design There are some jaw plates are designed to 1 piece or 2 pieces. Different designs suit different jaw crushers and working conditions. Normally, large jaw crusher jaw plates are originally designed to use a 2 piece jaw die design, whi...
Lee mas
Placa intermedia trituradora de mandíbula
por administrador el 20-11-13
Jaw Crusher Intermediate Plate The intermediate plate is an important jaw crusher wear parts. Fitting an intermediate (backing) plate behind the fixed jaw die reduces the nip angle of the crusher. The intermediate plate reduces the feed opening and the setting range by approximately the s...
Lee mas
Placa de protección de la trituradora de mandíbula
por administrador el 20-11-13
Jaw Crusher Protection Plate Protection plates are designed for additional protection of the crusher’s frame and pitman. They are recommended when using small settings (always greater than or equal to the minimum recommended setting) and/or when the rock to be crushed is very hard (i.e. v...
Lee mas
REEMPLAZO DE PLACA DE MORDAZA DE 1 PIEZA
por administrador el 20-11-13
1 PIECE JAW Plate REPLACEMENT Jaw plates can either be turned end for end or replaced depending on their wear. The jaw dies can be turned once after their installation before they need to be replaced. Dismantling Fixed Jaw Plates Clean the jaw die lifting holes. Remove stones and sand f...
Lee mas
REEMPLAZO DE MORDAZA DE 2 PIEZAS
por administrador el 20-11-13
2 PIECE JAW DIE REPLACEMENT Jaw dies can either be turned end for end or replaced depending on their wear. The jaw dies can be turned once after their installation before they need to be replaced. Fixed Jaw Die Clean the jaw die lifting holes. Remove stones and sand from the jaws. Remo...
Lee mas
Cámara de trituración de trituradora de mandíbula
por administrador el 20-11-13
Jaw Crusher Crushing Chamber To ensure optimum performance and cost-effective production it’s important to frequently inspect the following parts and to replace them before they are completely worn out. 3500-0 Deflector plate (moving jaw only) 3400-0 Clamping bar 3300-1 Jaw plate 3100-0...
Lee mas
Sistema de ajuste de la configuración de la trituradora de mandíbula
por administrador el 20-11-13
Jaw Crusher Setting Adjustment System Maintenance for these parts must be carried out only by trained or authorized personnel, but the inspection can be performed by the operator. Worn components should be replaced in good time to avoid damaging the toggle plate or toggle seats, with a co...
Lee mas
Cambio de placa de mordaza
por administrador el 20-11-13
Exchanging jaw plate After a long time running, jaw plates need an exchange. The following wear parts are required: A new fixed jaw plate A new movable jaw plate Never weld external lifting eyes to the jaw plates. Always use the referred lifting cavity on the jaw plate and the lifting ...
Lee mas
¿Cómo instalar la placa de mordaza?
por administrador el 20-11-13
Installing jaw plate There are some things that need to notice when installing jaw plates. 3500-0 Deflector plate (moving jaw) 3300-1 Jaw plate 3100-0 Wear plate 3200-0 Support bar. 1 Lifting cavity,2 Lifting tool. If planning to exchange wear plates (3100-0), cheek plates, deflector p...
Lee mas
Cambio de la placa de desgaste de la trituradora de mandíbula
por administrador el 20-11-13
Exchanging jaw crusher wear plate How to exchange jaw crusher wear plates? What needs notice when exchanging jaw crusher wear plate? 3000-0 Jaw (moving) 3100-0 Wear plate 3200-0 Support bar 3200-1 Lifting eye Recommended tools: Crow bar, Lifting tackle, and chain Mobile crane The follo...
Lee mas
Cambie e instale la placa lateral de la trituradora de mandíbula
por administrador el 20-11-13
Exchange and Install Jaw Crusher Cheek Plate Cheek plates are one of the most important jaw crusher wear parts. After a long time working, those cheek plates need exchange. How to exchange jaw crusher cheek plates? How to install jaw crusher cheek plates? How to exchange jaw crusher chee...
Lee mas
1
2
3
4
5
6
Siguiente>
>>
Página 1 / 14
Presione enter para buscar o ESC para cerrar
English
Spanish
French
German
Portuguese
Russian
Japanese
Korean
Arabic
Irish
Greek
Turkish
Italian
Danish
Romanian
Indonesian
Czech
Afrikaans
Swedish
Polish
Basque
Catalan