Casa
Chi siamo
Profilo Aziendale
storia dell'azienda
Il nostro vantaggio
I nostri prodotti
CrMo Mill Liner
Mn Steel Mill Liner
Fodera per acciaieria Cr
Fodera in acciaio legato
Parti del frantoio a mascelle
Parti del frantoio a cono
Parti del frantoio a martelli
Parti del frantoio a impatto
Mezzi di macinazione
Altri pezzi di ricambio
Servizio
Nostro servizio
Notizia
Contattaci
inglese
Casa
Notizia
Notizie del settore
Rapporto di usura delle parti di usura del frantoio a mascelle
da admin il 20-11-13
Jaw Crusher Wear Parts Wear Ratio Jaw crusher wear parts include: Upper cheek plates Lower cheek plates Movable jaw Fixed jaw In normal working conditions, different wear parts have different wear ratios. In order to avoid damage the jaw crusher, we must know every wear part wear ratio....
Per saperne di più
Confronti tra il design della piastra della ganascia da 1 pezzo e 2 pezzi
da admin il 20-11-13
Comparisons Between 1 piece and 2 piece jaw plate design There are some jaw plates are designed to 1 piece or 2 pieces. Different designs suit different jaw crushers and working conditions. Normally, large jaw crusher jaw plates are originally designed to use a 2 piece jaw die design, whi...
Per saperne di più
Piastra intermedia per frantoio a mascelle
da admin il 20-11-13
Jaw Crusher Intermediate Plate The intermediate plate is an important jaw crusher wear parts. Fitting an intermediate (backing) plate behind the fixed jaw die reduces the nip angle of the crusher. The intermediate plate reduces the feed opening and the setting range by approximately the s...
Per saperne di più
Piastra di protezione per frantoio a mascelle
da admin il 20-11-13
Jaw Crusher Protection Plate Protection plates are designed for additional protection of the crusher’s frame and pitman. They are recommended when using small settings (always greater than or equal to the minimum recommended setting) and/or when the rock to be crushed is very hard (i.e. v...
Per saperne di più
1 PEZZO PLACCA GANASCE DI SOSTITUZIONE
da admin il 20-11-13
1 PIECE JAW Plate REPLACEMENT Jaw plates can either be turned end for end or replaced depending on their wear. The jaw dies can be turned once after their installation before they need to be replaced. Dismantling Fixed Jaw Plates Clean the jaw die lifting holes. Remove stones and sand f...
Per saperne di più
2 PEZZI DI SOSTITUZIONE DELLA MATRICE A GANASCE
da admin il 20-11-13
2 PIECE JAW DIE REPLACEMENT Jaw dies can either be turned end for end or replaced depending on their wear. The jaw dies can be turned once after their installation before they need to be replaced. Fixed Jaw Die Clean the jaw die lifting holes. Remove stones and sand from the jaws. Remo...
Per saperne di più
Camera di frantumazione del frantoio a mascelle
da admin il 20-11-13
Jaw Crusher Crushing Chamber To ensure optimum performance and cost-effective production it’s important to frequently inspect the following parts and to replace them before they are completely worn out. 3500-0 Deflector plate (moving jaw only) 3400-0 Clamping bar 3300-1 Jaw plate 3100-0...
Per saperne di più
Sistema di regolazione dell'impostazione del frantoio a mascelle
da admin il 20-11-13
Jaw Crusher Setting Adjustment System Maintenance for these parts must be carried out only by trained or authorized personnel, but the inspection can be performed by the operator. Worn components should be replaced in good time to avoid damaging the toggle plate or toggle seats, with a co...
Per saperne di più
Sostituzione della piastra della mascella
da admin il 20-11-13
Exchanging jaw plate After a long time running, jaw plates need an exchange. The following wear parts are required: A new fixed jaw plate A new movable jaw plate Never weld external lifting eyes to the jaw plates. Always use the referred lifting cavity on the jaw plate and the lifting ...
Per saperne di più
Come installare la piastra della mascella?
da admin il 20-11-13
Installing jaw plate There are some things that need to notice when installing jaw plates. 3500-0 Deflector plate (moving jaw) 3300-1 Jaw plate 3100-0 Wear plate 3200-0 Support bar. 1 Lifting cavity,2 Lifting tool. If planning to exchange wear plates (3100-0), cheek plates, deflector p...
Per saperne di più
Sostituzione della piastra antiusura del frantoio a mascelle
da admin il 20-11-13
Exchanging jaw crusher wear plate How to exchange jaw crusher wear plates? What needs notice when exchanging jaw crusher wear plate? 3000-0 Jaw (moving) 3100-0 Wear plate 3200-0 Support bar 3200-1 Lifting eye Recommended tools: Crow bar, Lifting tackle, and chain Mobile crane The follo...
Per saperne di più
Sostituire e installare la guancia del frantoio a mascelle
da admin il 20-11-13
Exchange and Install Jaw Crusher Cheek Plate Cheek plates are one of the most important jaw crusher wear parts. After a long time working, those cheek plates need exchange. How to exchange jaw crusher cheek plates? How to install jaw crusher cheek plates? How to exchange jaw crusher chee...
Per saperne di più
1
2
3
4
5
6
Avanti >
>>
Pagina 1 / 14
Premi invio per cercare o ESC per chiudere
English
Italian
French
German
Portuguese
Spanish
Russian
Japanese
Korean
Arabic
Irish
Greek
Turkish
Danish
Romanian
Indonesian
Czech
Afrikaans
Swedish
Polish
Basque
Catalan