Dom
O nas
profil firmy
Historia firmy
Nasza przewaga
Nasze produkty
CrMo Mill Liner
Mn stalowa wkładka
Wkładka do stalowni Cr
Wykładzina ze stali stopowej
Części do kruszarek szczękowych
Części do kruszarek stożkowych
Części do kruszarek młotkowych
Części do kruszarek udarowych
Szlifowanie mediów
Inne części zamienne
Usługa
Nasze usługi
Aktualności
Skontaktuj się z nami
język angielski
Dom
Aktualności
Wiadomości branżowe
Współczynnik zużycia części kruszarki szczękowej
przez administratora dnia 20-11-13
Jaw Crusher Wear Parts Wear Ratio Jaw crusher wear parts include: Upper cheek plates Lower cheek plates Movable jaw Fixed jaw In normal working conditions, different wear parts have different wear ratios. In order to avoid damage the jaw crusher, we must know every wear part wear ratio....
Czytaj więcej
Porównania Między 1-częściową i 2-częściową płytą szczękową
przez administratora dnia 20-11-13
Comparisons Between 1 piece and 2 piece jaw plate design There are some jaw plates are designed to 1 piece or 2 pieces. Different designs suit different jaw crushers and working conditions. Normally, large jaw crusher jaw plates are originally designed to use a 2 piece jaw die design, whi...
Czytaj więcej
Płyta pośrednia kruszarki szczękowej
przez administratora dnia 20-11-13
Jaw Crusher Intermediate Plate The intermediate plate is an important jaw crusher wear parts. Fitting an intermediate (backing) plate behind the fixed jaw die reduces the nip angle of the crusher. The intermediate plate reduces the feed opening and the setting range by approximately the s...
Czytaj więcej
Płyta ochronna kruszarki szczękowej
przez administratora dnia 20-11-13
Jaw Crusher Protection Plate Protection plates are designed for additional protection of the crusher’s frame and pitman. They are recommended when using small settings (always greater than or equal to the minimum recommended setting) and/or when the rock to be crushed is very hard (i.e. v...
Czytaj więcej
1 CZĘŚĆ WYMIANA PŁYTY SZCZĘKI
przez administratora dnia 20-11-13
1 PIECE JAW Plate REPLACEMENT Jaw plates can either be turned end for end or replaced depending on their wear. The jaw dies can be turned once after their installation before they need to be replaced. Dismantling Fixed Jaw Plates Clean the jaw die lifting holes. Remove stones and sand f...
Czytaj więcej
2 CZĘŚCIOWA WYMIANA MATRYCY SZCZĘKI
przez administratora dnia 20-11-13
2 PIECE JAW DIE REPLACEMENT Jaw dies can either be turned end for end or replaced depending on their wear. The jaw dies can be turned once after their installation before they need to be replaced. Fixed Jaw Die Clean the jaw die lifting holes. Remove stones and sand from the jaws. Remo...
Czytaj więcej
Komora kruszenia kruszarki szczękowej
przez administratora dnia 20-11-13
Jaw Crusher Crushing Chamber To ensure optimum performance and cost-effective production it’s important to frequently inspect the following parts and to replace them before they are completely worn out. 3500-0 Deflector plate (moving jaw only) 3400-0 Clamping bar 3300-1 Jaw plate 3100-0...
Czytaj więcej
System regulacji ustawienia kruszarki szczękowej
przez administratora dnia 20-11-13
Jaw Crusher Setting Adjustment System Maintenance for these parts must be carried out only by trained or authorized personnel, but the inspection can be performed by the operator. Worn components should be replaced in good time to avoid damaging the toggle plate or toggle seats, with a co...
Czytaj więcej
Wymiana płyty szczęki
przez administratora dnia 20-11-13
Exchanging jaw plate After a long time running, jaw plates need an exchange. The following wear parts are required: A new fixed jaw plate A new movable jaw plate Never weld external lifting eyes to the jaw plates. Always use the referred lifting cavity on the jaw plate and the lifting ...
Czytaj więcej
Jak zainstalować płytkę szczękową?
przez administratora dnia 20-11-13
Installing jaw plate There are some things that need to notice when installing jaw plates. 3500-0 Deflector plate (moving jaw) 3300-1 Jaw plate 3100-0 Wear plate 3200-0 Support bar. 1 Lifting cavity,2 Lifting tool. If planning to exchange wear plates (3100-0), cheek plates, deflector p...
Czytaj więcej
Wymiana płyty ścieralnej kruszarki szczękowej
przez administratora dnia 20-11-13
Exchanging jaw crusher wear plate How to exchange jaw crusher wear plates? What needs notice when exchanging jaw crusher wear plate? 3000-0 Jaw (moving) 3100-0 Wear plate 3200-0 Support bar 3200-1 Lifting eye Recommended tools: Crow bar, Lifting tackle, and chain Mobile crane The follo...
Czytaj więcej
Wymiana i instalacja płyty policzkowej kruszarki szczękowej
przez administratora dnia 20-11-13
Exchange and Install Jaw Crusher Cheek Plate Cheek plates are one of the most important jaw crusher wear parts. After a long time working, those cheek plates need exchange. How to exchange jaw crusher cheek plates? How to install jaw crusher cheek plates? How to exchange jaw crusher chee...
Czytaj więcej
1
2
3
4
5
6
Dalej >
>>
Strona 1 / 14
Naciśnij Enter, aby wyszukać lub ESC, aby zamknąć
English
Polish
French
German
Portuguese
Spanish
Russian
Japanese
Korean
Arabic
Irish
Greek
Turkish
Italian
Danish
Romanian
Indonesian
Czech
Afrikaans
Swedish
Basque
Catalan