Главная
О нас
Профиль компании
История компании
Наши преимущества
Наши продукты
Футеровка мельницы CrMo
Футеровка сталелитейного завода Mn
Футеровка сталелитейного завода Cr
Футеровка из легированной стали
Щековая плита
Части конусной дробилки
Части молотковой дробилки
Детали ударной дробилки
Мелющие тела
Другие запасные части
Сервис
Наш сервис
Новости
Контакты
Английский
Главная
Новости
Новости отрасли
Коэффициент износа изнашиваемых деталей щековой дробилки
от администратора 20-11-13
Jaw Crusher Wear Parts Wear Ratio Jaw crusher wear parts include: Upper cheek plates Lower cheek plates Movable jaw Fixed jaw In normal working conditions, different wear parts have different wear ratios. In order to avoid damage the jaw crusher, we must know every wear part wear ratio....
См. ещё
Сравнение односоставной и двухсоставной конструкции челюстной пластины
от администратора 20-11-13
Comparisons Between 1 piece and 2 piece jaw plate design There are some jaw plates are designed to 1 piece or 2 pieces. Different designs suit different jaw crushers and working conditions. Normally, large jaw crusher jaw plates are originally designed to use a 2 piece jaw die design, whi...
См. ещё
Промежуточная пластина щековой дробилки
от администратора 20-11-13
Jaw Crusher Intermediate Plate The intermediate plate is an important jaw crusher wear parts. Fitting an intermediate (backing) plate behind the fixed jaw die reduces the nip angle of the crusher. The intermediate plate reduces the feed opening and the setting range by approximately the s...
См. ещё
Защитная пластина щековой дробилки
от администратора 20-11-13
Jaw Crusher Protection Plate Protection plates are designed for additional protection of the crusher’s frame and pitman. They are recommended when using small settings (always greater than or equal to the minimum recommended setting) and/or when the rock to be crushed is very hard (i.e. v...
См. ещё
ЗАМЕНА ЧЕЛЮСТНОЙ ПЛИТЫ, 1 ШТ.
от администратора 20-11-13
1 PIECE JAW Plate REPLACEMENT Jaw plates can either be turned end for end or replaced depending on their wear. The jaw dies can be turned once after their installation before they need to be replaced. Dismantling Fixed Jaw Plates Clean the jaw die lifting holes. Remove stones and sand f...
См. ещё
ЗАМЕНА МАТРИЦЫ ИЗ 2 ЧАСТЕЙ
от администратора 20-11-13
2 PIECE JAW DIE REPLACEMENT Jaw dies can either be turned end for end or replaced depending on their wear. The jaw dies can be turned once after their installation before they need to be replaced. Fixed Jaw Die Clean the jaw die lifting holes. Remove stones and sand from the jaws. Remo...
См. ещё
Щековая дробилка Дробильная камера
от администратора 20-11-13
Jaw Crusher Crushing Chamber To ensure optimum performance and cost-effective production it’s important to frequently inspect the following parts and to replace them before they are completely worn out. 3500-0 Deflector plate (moving jaw only) 3400-0 Clamping bar 3300-1 Jaw plate 3100-0...
См. ещё
Система регулировки настройки щековой дробилки
от администратора 20-11-13
Jaw Crusher Setting Adjustment System Maintenance for these parts must be carried out only by trained or authorized personnel, but the inspection can be performed by the operator. Worn components should be replaced in good time to avoid damaging the toggle plate or toggle seats, with a co...
См. ещё
Замена челюстной пластины
от администратора 20-11-13
Exchanging jaw plate After a long time running, jaw plates need an exchange. The following wear parts are required: A new fixed jaw plate A new movable jaw plate Never weld external lifting eyes to the jaw plates. Always use the referred lifting cavity on the jaw plate and the lifting ...
См. ещё
Как установить челюстную пластину?
от администратора 20-11-13
Installing jaw plate There are some things that need to notice when installing jaw plates. 3500-0 Deflector plate (moving jaw) 3300-1 Jaw plate 3100-0 Wear plate 3200-0 Support bar. 1 Lifting cavity,2 Lifting tool. If planning to exchange wear plates (3100-0), cheek plates, deflector p...
См. ещё
Замена изнашиваемой пластины щековой дробилки
от администратора 20-11-13
Exchanging jaw crusher wear plate How to exchange jaw crusher wear plates? What needs notice when exchanging jaw crusher wear plate? 3000-0 Jaw (moving) 3100-0 Wear plate 3200-0 Support bar 3200-1 Lifting eye Recommended tools: Crow bar, Lifting tackle, and chain Mobile crane The follo...
См. ещё
Замена и установка щековой пластины щековой дробилки
от администратора 20-11-13
Exchange and Install Jaw Crusher Cheek Plate Cheek plates are one of the most important jaw crusher wear parts. After a long time working, those cheek plates need exchange. How to exchange jaw crusher cheek plates? How to install jaw crusher cheek plates? How to exchange jaw crusher chee...
См. ещё
1
2
3
4
5
6
След. >
>>
Страница 1 / 14
Нажмите "Enter" для поиска или "ESC " чтобы закрыть
English
Russian
French
German
Portuguese
Spanish
Japanese
Korean
Arabic
Irish
Greek
Turkish
Italian
Danish
Romanian
Indonesian
Czech
Afrikaans
Swedish
Polish
Basque
Catalan