Ev
Hakkımızda
Şirket Profili
Şirket Geçmişi
Bizim avantajımız
Bizim ürünlerimiz
CrMo Mill Liner
Mn Çelik Fabrikası Liner
Cr Çelik Fabrikası Liner
Alaşımlı Çelik Fabrikası Liner
Çeneli Kırıcı Parçaları
Koni Kırıcı Parçaları
Çekiçli Kırıcı Parçaları
Darbeli Kırıcı Parçaları
Taşlama Ortamı
Diğer Yedek Parçalar
Hizmet
Servisimiz
Haberler
Bize Ulaşın
ingilizce
Ev
Haberler
Endüstri Haberleri
Çeneli Kırıcı Aşınma Parçaları Aşınma Oranı
20-11-13 tarihinde admin tarafından
Jaw Crusher Wear Parts Wear Ratio Jaw crusher wear parts include: Upper cheek plates Lower cheek plates Movable jaw Fixed jaw In normal working conditions, different wear parts have different wear ratios. In order to avoid damage the jaw crusher, we must know every wear part wear ratio....
Daha fazla oku
1 parça ve 2 parça çene plakası tasarımı arasındaki karşılaştırmalar
20-11-13 tarihinde admin tarafından
Comparisons Between 1 piece and 2 piece jaw plate design There are some jaw plates are designed to 1 piece or 2 pieces. Different designs suit different jaw crushers and working conditions. Normally, large jaw crusher jaw plates are originally designed to use a 2 piece jaw die design, whi...
Daha fazla oku
Çeneli Kırıcı Ara Plaka
20-11-13 tarihinde admin tarafından
Jaw Crusher Intermediate Plate The intermediate plate is an important jaw crusher wear parts. Fitting an intermediate (backing) plate behind the fixed jaw die reduces the nip angle of the crusher. The intermediate plate reduces the feed opening and the setting range by approximately the s...
Daha fazla oku
Çeneli Kırıcı Koruma Plakası
20-11-13 tarihinde admin tarafından
Jaw Crusher Protection Plate Protection plates are designed for additional protection of the crusher’s frame and pitman. They are recommended when using small settings (always greater than or equal to the minimum recommended setting) and/or when the rock to be crushed is very hard (i.e. v...
Daha fazla oku
1 ADET ÇENE PLAKASI DEĞİŞİMİ
20-11-13 tarihinde admin tarafından
1 PIECE JAW Plate REPLACEMENT Jaw plates can either be turned end for end or replaced depending on their wear. The jaw dies can be turned once after their installation before they need to be replaced. Dismantling Fixed Jaw Plates Clean the jaw die lifting holes. Remove stones and sand f...
Daha fazla oku
2 ADET ÇENE KALIP DEĞİŞİMİ
20-11-13 tarihinde admin tarafından
2 PIECE JAW DIE REPLACEMENT Jaw dies can either be turned end for end or replaced depending on their wear. The jaw dies can be turned once after their installation before they need to be replaced. Fixed Jaw Die Clean the jaw die lifting holes. Remove stones and sand from the jaws. Remo...
Daha fazla oku
Çeneli Kırıcı Kırma Odası
20-11-13 tarihinde admin tarafından
Jaw Crusher Crushing Chamber To ensure optimum performance and cost-effective production it’s important to frequently inspect the following parts and to replace them before they are completely worn out. 3500-0 Deflector plate (moving jaw only) 3400-0 Clamping bar 3300-1 Jaw plate 3100-0...
Daha fazla oku
Çeneli Kırıcı Ayar Ayar Sistemi
20-11-13 tarihinde admin tarafından
Jaw Crusher Setting Adjustment System Maintenance for these parts must be carried out only by trained or authorized personnel, but the inspection can be performed by the operator. Worn components should be replaced in good time to avoid damaging the toggle plate or toggle seats, with a co...
Daha fazla oku
Değişen çene plakası
20-11-13 tarihinde admin tarafından
Exchanging jaw plate After a long time running, jaw plates need an exchange. The following wear parts are required: A new fixed jaw plate A new movable jaw plate Never weld external lifting eyes to the jaw plates. Always use the referred lifting cavity on the jaw plate and the lifting ...
Daha fazla oku
Çene plakası nasıl kurulur?
20-11-13 tarihinde admin tarafından
Installing jaw plate There are some things that need to notice when installing jaw plates. 3500-0 Deflector plate (moving jaw) 3300-1 Jaw plate 3100-0 Wear plate 3200-0 Support bar. 1 Lifting cavity,2 Lifting tool. If planning to exchange wear plates (3100-0), cheek plates, deflector p...
Daha fazla oku
Değiştirme çeneli kırıcı aşınma plakası
20-11-13 tarihinde admin tarafından
Exchanging jaw crusher wear plate How to exchange jaw crusher wear plates? What needs notice when exchanging jaw crusher wear plate? 3000-0 Jaw (moving) 3100-0 Wear plate 3200-0 Support bar 3200-1 Lifting eye Recommended tools: Crow bar, Lifting tackle, and chain Mobile crane The follo...
Daha fazla oku
Çeneli Kırıcı Yanak Plakasını Değiştirin ve Takın
20-11-13 tarihinde admin tarafından
Exchange and Install Jaw Crusher Cheek Plate Cheek plates are one of the most important jaw crusher wear parts. After a long time working, those cheek plates need exchange. How to exchange jaw crusher cheek plates? How to install jaw crusher cheek plates? How to exchange jaw crusher chee...
Daha fazla oku
1
2
3
4
5
6
Sonraki >
>>
Sayfa 1 / 14
Aramak için enter'a veya kapatmak için ESC'ye basın
English
Turkish
French
German
Portuguese
Spanish
Russian
Japanese
Korean
Arabic
Irish
Greek
Italian
Danish
Romanian
Indonesian
Czech
Afrikaans
Swedish
Polish
Basque
Catalan